你的位置:电感厂 > 新闻动态功率电感

ST MP34DT01和STM32数字MEMS麦克风解决方案

2015-12-15 07:42:04      点击次数:
上一篇:基于OID的物联网统一标识体系介绍 贴片电感

ST 公司的MP34DT01是超小型低功耗全方位数字MEMS麦克风,具有容性传感元件和IC接口,单电源工作,声学过载点120 dBSPL,信噪比63dB,全方位灵敏度,灵敏度-26dBFC,PDM输出,主要用在手机,笔记本电脑,手持媒体播放器(PMP),VoIP,语音识别,数码相机和摄像机,防盗系统等.本文介绍了MP34DT01主要特性,以及采用MP34DT01和STM32 MCU的STEVAL-MKI117V1演示板主要特性,电路图,材料清单和PCB布局图.

The MP34DT01 is an ultra-compact, low-power,omnidirectional, digital MEMS microphone built with a capacitive sensing element and an IC interface.

The sensing element, capable of detecting acoustic waves, is manufactured using a specialized silicon micromachining process dedicated to produce audio sensors.

The IC interface is manufactured using a CMOS process that allows designing a dedicated circuit able to provide a digital signal externally in PDM format.

The MP34DT01 has an acoustic overload point of 120 dBSPL with a 63 dB signal-to-noise ratio and –26 dBFS sensitivity.

The MP34DT01 is ava片式电感器的用途ilable in a top-port, SMDcompliant, EMI-shielded package and is guaranteed to operate over an extended temperature range from -30℃ to +70℃.

MP34DT01主要特性:

■ Single supply voltage

■ Low power consumption

■ 120 dBSPL acoustic overload point

■ 63 dB signal-to-noise ratio

■ Omnidirectional sensitivity

■ –26 dBFS sensitivity

■ PDM output

■ HCLGA package

– Top-port design

SMD-compliant

– EMI-shielded

– ECOPACK® , RoHS, and “Green” compliant

MP34DT01应用:

■ Mobile terminals

■ Laptop and notebook computers

■ Portable media players

■ VoIP

■ Speech recognition

■ A/V eLearning devices

■ Gaming and virtual reality input devices

■ Digital still and video cameras

■ Antitheft systems

MEMS microphone demonstration board based on the MP34DT01 and STM32

The purpose of the STEVAL-MKI117V1 demonstration board is to provide an exa绕线电感mple of the decoding and streaming of digital MEMS microphone outputs.

The STEVAL-MKI117V1 demonstration board hosts the MP34DT01 (bottom-port digital microphone), working as a sensor, and the STM32F107RC microcontroller, working as an audio decoder.

These microphones are analog-to-digital transducers. They are able to sense sound pressure and convert this signal into a digita扁平线圈电感器工厂l signal using the PDM technique.

The STM32 microcontroller decodes the PDM signal coming from the microphones and streams the audio via the USB.

The STEVAL-MKI117V1 demonstration board is a sound card automatically recognized by the PC as an audio device. Connection is made through a USB cable which also supplies the board and then streams the collected audio.

STEVAL-MKI117V1演示板主要特性:

■ Powered and connected to PC through USB

■ Sound card automatically recognized by the PC as an audio device

■ The onboard microphones are digital MEMS devices

■ MEMS microphones provide a high frequency data stream (1 to 3.25 MHz) of 1-bit digital samples (PDM technique)

■ Audio collected from the microphones is sent to the PC through the USB

■ LED status indicator

■ RoHS compliant

图1.STEVAL-MKI117V1演示板外形图:左,顶视图,右,底视图


图2.STEVAL-MKI117V1演示板电路图(1)

图3.STEVAL-MKI117V1演示板电路图(2)
STEVAL-MKI117V1演示板材料清单:




图4.STEVAL-MKI117V1演示板PCB布局图:顶层

图5.STEVAL-MKI117V1演示板PCB布局图:底层
详情请见:
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/DM00039779.pdf大电流电感

  • 新手求教,UC3843没有输出,怎样判断UC3843的好坏? 一直都想给自己做个开关电源用,刚好年末事少就参照论团网友的设计经验,试着做了一块板子,结果 没!工!作!啊!


    检查电路发现UC3843的6脚没输出,请大家看一下这个电路那些地方有问

  • MCU供电电源芯片选型(看哪些参数)?目前STM32单片机和LAN9252在3.3V电源轨上消耗500mA,现在方案是24V通过DCDC降到5V,5V通过隔离电源到隔离5V,隔离5V通过线性电源到3.3V.问题点:1、LM1117-3.3是否靠谱,目前方案使用MCP1727到3.3V,换成LM1117是否靠谱?(看哪些参数)2、线性电源芯片转换效率怎么考虑?选型时需要加上裕量,现在500mAx3.3V= 1.65W,1.65w/0.6=2.7w,线性电源选型按2.7W是否可靠1.给数字部分供电对噪声和纹波要求不高,重点看Dropout电压参数

  • 莱士方案求指导 如图,我用LIS8516做了一款280mA/76V=24W的驱动,现在加了填谷电路也只有0.86PF的功率因数,客户要求说做到0.9PF以上,小生试过多种方法仍没效果,求大师们给个指导,加什么器件?怎么

  • YBPOO防近视智能笔
  • 为什么电网中存在有功功率与无功功率?
  • EMI/EMC设计PCB被动组件的隐藏行为和特性解析
  • 需找IC 内置COOL MOS的IC PSR 可以做5V2A的
  • LED电源EMC问题
  • 开关电源给若干串联电池模块供电问题
  • [稳压电源]有没有使用过TTL电平控制28V电源开关
  • 线圈电感
  • 基于较大功率的直流电机H桥驱动电路方案
  • 高频铁氧体变压器 电感 频率匹配问题